Ferrari F40 LM Restoration Part 1

Could this be the holy grail? The best car ever featured on Build-Threads.com? For those of you who are keen followers of the Facebook page, you’d be well aware that I’m quite the Ferrari tragic, and that as far as supercars go, I’d have a hard time deciding between an F40 or a Lamborghini Miura (if the opportunity ever happened to arise). I’m that much of a tragic, in fact, that I signed up to Ferrari Chat a long time ago just so I could view images that are restricted to members. This build comes from that very forum, but I’m not about to make you sign up to view it. Instead, I have personally asked the owner of this car, Tim, for his permission to re-post the entire thread on these very pages, and thankfully he said yes. I think this build is so incredible that it should be shared with a greater audience, so I’d like to thank Tim for allowing me to post it here.

This F40 is listed as Chassis No 84326, and was rotting away in a garage for 8 years before Tim snapped it up and sought about having it brought back to better than it’s former glory. This isn’t a made-for-TV hack job, this is a no-expense-spared restoration of one of the greatest supercars of all time. I’m so used to seeing F40’s in their finished guise, carefully polished with gleaming paintwork, but to see one in various states of undress has given me a whole new appreciation for both the shape and the engineering behind it. I hope you enjoy this build as much as I have…

All text and images below are taken from http://www.ferrarichat.com/forum/288gto-f40-f50-enzo-laferrari/396915-f40-lm-restoration.html

As some of you may have read the thread about chassis 84326, a non Michelotto F40LM which raced in the BPR in 96 and which had been rotting in a garage for 8 years and I bought a few months ago. Described by Mike Sheehan as LM/GTE it is one of 27 non original cars converted by privateers.

Aside from the original Michelotto LM’s, the 27 other cars as listed by Michael Sheehan in his definitive article on the LM, all started their life as road cars. 84326 was no different and finally ended up in an unusual configuration running twin KKK turbos with twin waste gates and adjustable boost putting out approx 720 BHP. It competed in some races in the 1996 BPR without any distinction and probably it’s greatest claim to fame was that it lapped Hockenheim quicker, just, than a Maclaren FI GTR, so it was no slouch. It is also featured in the book covering the series.

When I bought it, it looked good as per images I will post in a next instalment, but once we got into the detail, it turned out it was a real mess, and 8 years in a damp barn had taken their toll.

The real issue has been whether to restore or continue its evolution and I eventually decided that I would continue its evolution seeing as how it achieved no great success on track in its original format and has continued to evolve during its life so might as well continue now. Consequently, as it is described by Michael Sheehan as an LM/GTE, I thought I might as well continue updating it accordingly.

So, we have stripped her down to almost a bare shell, and the aim is to upgrade all areas to full spec whilst leaving the engine as it raced, and we are lucky in that Michelotto has agreed to supply us with parts, specifically brakes, hubs, suspension etc which he is normally not happy to do unless for an ex race car.

Thanks to our Dutch friends on F Chat, I have managed to unearth its history and as chronologically we should start there, here are some great shots courtesy of them during the 1996 BPR.

Next up a few more race shots and then where we started, somewhat of an illusion.

1655145d1360159252-f40-lm-restoration-image-30

1655146d1360159252-f40-lm-restoration-image-29

1655144d1360159252-f40-lm-restoration-image-28

1655143d1360159252-f40-lm-restoration-image-27

No, I won’t campaign her but use primarily on the track for fun. Hope to follow the Mille Miglia in the Ferrari parade perhaps and do a few events. Work is being done by a small shop in the UK called Mototechnique who I know from old when they rebuilt my 365 Spyder and they recently did a full ground up on a 250 GTO, so they know their stuff-real old fashioned artisans.

A few more images as was
1655665d1360244479-f40-lm-restoration-image-22

1655666d1360244479-f40-lm-restoration-image-23

1657187d1360457362-f40-lm-restoration-photo

1657188d1360457362-f40-lm-restoration-image-20

1657192d1360457618-f40-lm-restoration-image-28a

1657193d1360457618-f40-lm-restoration-image-23

1657194d1360457618-f40-lm-restoration-18a

1657191d1360457618-f40-lm-restoration-image-17

Car was delivered to a small restoration company, Mototechnique in Surrey England who restored my old Daytona Spyder 25 years ago and seems to have got even better having recently done a ground up 250 GTO restoration.

The strip down begins and note the Air Jack inlet just behind the door which we will recite in the lower rear clam as well as sorting the shut line.

Also, now the intercoolers are out, they are somewhat deeper than at first glance.

1657863d1360591166-f40-lm-restoration-0801-036

1657864d1360591166-f40-lm-restoration-0801-001

1657866d1360591235-f40-lm-restoration-0801-014

1657865d1360591235-f40-lm-restoration-9th-1st-031

1657862d1360591166-f40-lm-restoration-9th-1st-038

 A few more images as the beautiful body is removed to show the mess beneath.

The strengthened wishbones which now are to be replaced with all new Michelotto ones, the modified front assembly still with its vestiges of road car use, the oil rad which had been bizarrely resited to the front, all headed for the bin!

1658320d1360674371-f40-lm-restoration-1101-008-copy

1658322d1360674371-f40-lm-restoration-image-91

1658323d1360674371-f40-lm-restoration-image-89

1658324d1360674650-f40-lm-restoration-image-3

 

More images of suspension and brakes, all heading for the bin. Apparently in 96 these were genuine Group C but in my mind have no place on this car. All very interesting but off they come.

You can also see the disaster that are the old fuel tanks which also join the growing scarp heap. More about those later.

Afraid the next few posts are all going to be about stripping before we can focus on rebuilding and evolving this car as it would have been, had a team had the interest, and money, to do so.

4 weeks to get the chassis prepared before a large and very expensive package arrives from the delightful and hugely knowledgeable Cristiano Michelotto. About the most exciting birthday present (mine is in March)I could imagine opening.

1658700d1360761802-f40-lm-restoration-image-83

1658701d1360761802-f40-lm-restoration-image-93

1658702d1360761802-f40-lm-restoration-image-29

1658703d1360761802-f40-lm-restoration-image-58

A couple more shots of the interior as it all comes apart. The wiring was a mess, added to and cut out with no logic-German engineering? Hardly. Note the large red fog light in the first image hanging down to the left of the wheel. Believe it or not that was an oil pressure light. Clearly the driver was going to have a hard time explaining if he had grenaded the engine due to low oil pressure. Simple, ugly, effective but now history. Remains of the Fire extinguisher system on the floor which will also be replaced. Given what we found and to be revealed in a future post, it could well have come in handy. Had it been charged.

We then got the chassis on the computerised jig to set all our minds at rest and amazingly it was good news for a change: ‘the straightest F40’ they had ever come across, and they have done a few. Great to know we have a really good undamaged and true base to build up on given the history and the time and money being invested. All measurements have been recorded for the future as in due course I will put a book together on the history and the journey from start to finish as a permanent record.

Engine and gearbox still in situ at this stage as needed for checking panel clearances in the body shop so they are correctly stressed as well as ensuring we get the right clearances on the fuel tanks as they are very close to the manifolds. More on the fuel tank saga with the next post, as that was another discovery, but here, as you can see, we have now got them out and they too have gone to the bin.

1659257d1360847689-f40-lm-restoration-image-4

1659258d1360847689-f40-lm-restoration-image

1659256d1360847689-f40-lm-restoration-image-3

1659255d1360847689-f40-lm-restoration-image-1

Whilst all the mechanicals get stripped out, a bit of work has started on the bodywork. All LM addenda removed and the prep works starts. Perspex out for repolishing.

For a mad moment I thought of changing colour and then realised that was insane. She stays red.

1659484d1360882217-f40-lm-restoration-image-6

1659485d1360882217-f40-lm-restoration-image-5

All the discs have spider cracks after hard racing so they are gone. Both hubs and discs will be replaced with beautiful lightweight Michelotto LM discs and hubs. One hub also totally finished so just as well.

Pedal box en route back to Michelotto for some minor adjustment pending a brand new full magnesium LM one which will take a few months, so at least we can keep going. Apparently they are producing some new ones for a customer who has their cars in inclement conditions and need replacing and so we will wait for that.

Once fitted, this will include the in car brake bias adjustment facility.

1659787d1360952215-f40-lm-restoration-3a

1659786d1360952215-f40-lm-restoration-image-1a 1659785d1360952215-f40-lm-restoration-image7a

Well we now have the manifolds and turbos out. Unusually this car ran twin KKKs with twin waste gates and produced about 640 BHP before it was fitted with adjustable boost which apparently took it to 720.

Anyway, no surprise that this is all in as bad condition as the rest of it. Turbos and wastegates off to a specialist for rebuilding and refinishing, the wastegates needing to have specific care taken so they dont blow off even slightly early. Everything will be cleaned up and probably ceramic coated.

The destruction continues.

1660452d1361110608-f40-lm-restoration-image-3a

1660451d1361110608-f40-lm-restoration-image-7

1660450d1361110608-f40-lm-restoration-image-4a

1660449d1361110608-f40-lm-restoration-image-1b

Finally a first sign of some construction, limited though it may be.

Whilst we have the chassis on the jig and importantly the engine still in, we are changing the single LM cross brace to the more rigid GTE style.

1660988d1361215728-f40-lm-restoration-image-1

 

1660989d1361215728-f40-lm-restoration-image-2

Construction again!

This is the fuel tank saga. In short they very badly needed replacing.

Original car ran with tanks cloaked in a sort of rubberised paint and were well past their sell by date. They are different to road tanks as fuel pumps etc are external for racing. We looked at fitting new cells which only have a 5 or possibly 10 year life(jury seems to be out on this) and as I plan on keeping this car a long time, we decided we did not want to have to take her apart again in a few years time, so we wanted to do better and evolve. Also as the US cars had alloy tanks, this was hardly stepping into the unknown.

Consequently we decided to avail ourselves of Mototechnique’s metalworking skills and fabricate our own. The interiors are being sanded to provide a key for a sealant, and then the tanks themselves will be clad in carbon fibre and then filled with foam. This solution is FIA approved so the car can still race if we ever wanted to and yet provides a belt and braces solution which takes advantage of modern developments in materials, has no weight penalty (possibly a small saving), and will hopefully last the life of the car. More detail as they get built up but here you can at least see the start, together with dry fitting in the chassis as they go along.

If, in years ahead when I am gone and the car is with a new owner, anyone who was totally hung up on originality can always revert to the cells, should they still be available.

Always amazed at the skill of someone taking a flat piece of metal and teasing it and cajoling it into complex shapes. I could not even do that with paper.

1661697d1361312228-f40-lm-restoration-image8a

1661698d1361312228-f40-lm-restoration-image-1a

1661699d1361312228-f40-lm-restoration-image-5a

1661700d1361312228-f40-lm-restoration-image-3a

Finally a filthy engine is released. 24 years of road and racing grime removed in a few hours and what a result. We then will break down the gearbox and on Michelotto’s recommendation, replace second gear as it is apparently a known weak spot when you start pumping more power through it, especially when used in anger as in racing. Also considering changing the crown wheel and pinion as apparently this car ran in excess of 220 and again on his advice, he suggests a reduction to give us a top speed of about 190/195 which is what he gears his current race cars to, even at Le Mans. The gain, obviously, is in acceleration.

Note still dry fitting the tanks as they are gradually made up, but in a week or so they should be all clad in carbon and good to go.

Whilst we have the engine out and broken down, thinking about pulling the heads just to check as it would be a shame to go this far only to find some problem later. Apparently recently rebuilt but after what we have found so far, it might be nice to see for ourselves.

1662936d1361538543-f40-lm-restoration-image-4b

 

1662937d1361538543-f40-lm-restoration-image-2b

1662939d1361538543-f40-lm-restoration-image-1b

 

 

1662938d1361538543-f40-lm-restoration-image-3b

 Universal joints needs sorting but drive shafts are good

1662945d1361540627-f40-lm-restoration-250113-001

A few more shots of fuel tank artwork.
1664113d1361735035-f40-lm-restoration-310113-001
1664114d1361735035-f40-lm-restoration-310113-005
1664115d1361735035-f40-lm-restoration-130213-005
1665509d1361961019-f40-lm-restoration-1402-003
Slowly reducing the car to individual pieces! At this rate I can see the house going, but doing it right is becoming more addictive than drugs.
1664616d1361828400-f40-lm-restoration-150313-031
1664617d1361828400-f40-lm-restoration-150313-026
Well, the alloy tanks are effectively finished save for some lugs and heatshields, and shortly, thanks to this forum, we will start to dress them in fibreglass and then the Carbon. You can see one old, slightly singed tank and the new one alongside. Cannot wait to seem them wrapped and finished but suspect that might be a week or so away.My outrageously priced birthday present, well hardly a present, from Michelotto should be shipping at the end of next week so that should really prove to be a turning point when we get our hands on that stuff. Big box opening moment when that arrives. All in all I am hoping that in a couple of weeks or so we can start proper construction and begin to assemble.Generally progress has been slower than I would have liked due to pressure at the shop, but we are still moving forward and learning every inch of the way.
1665901d1362052519-f40-lm-restoration-19213-007s
1665902d1362052519-f40-lm-restoration-19213-006
1665903d1362052519-f40-lm-restoration-19213-004
1665904d1362052519-f40-lm-restoration-19213-001
Well, a last gasp for attention for a week or so before the F70 launch when there will be only one thread to follow.I wont bore you with the ongoing work to the fuel tanks for now but we are almost getting to the bottom of the destruction phase. Here she is, down to basics, shortly to be masked up and off to the sand blasters who will strip off all the old chassis paint so we can get back to bare metal, prime and recoat in the correct Michelotto silver. Considered doing it manually and then came to the conclusion that the only way to get into every nook and remove all the grime was to blast it and that way we will get a perfect finish.There is that word again, ‘Perfect’ which normally equates to $.
1667237d1362308903-f40-lm-restoration-20th-feb-2-
1667232d1362307534-f40-lm-restoration-image1.jpg
Here are the heat shield lugs that have been attached to the tanks now and the very start of the laying up process.
1667462d1362341356-f40-lm-restoration-27th0213-031
1667463d1362341356-f40-lm-restoration-27th0213-033
1667464d1362341356-f40-lm-restoration-27feb03-006
1667465d1362341356-f40-lm-restoration-27feb03-005
Shell now all masked up and ready to have the chassis back to bare metal so should be the last time I see that in black. Meanwhile gearbox tear down has revealed that reverse gear is now useless and that has created a whole bunch of issues as Ferrari want to sell you reverse, Ist and the main shaft for $15K, so we have to find our way round that which may mean getting the part made up. More on this to follow.
1669502d1362649000-f40-lm-restoration-18th-13-002
1669503d1362649000-f40-lm-restoration-18th-13-003
1669504d1362649000-f40-lm-restoration-18th-13-004
1669505d1362649000-f40-lm-restoration-27feb03-002
We have now just about finished the front structure save for the locking pins etc and to remind you here is a photo of what went before. The weight saving is dramatic, the new unit being mere ounces.Interesting to note the modified central battery position and twin jacking points of the original. We are maintaining the battery position and replacing the jacks with Krontec units as used in F1 and most top end GT cars.
1672015d1363024555-f40-lm-restoration-12th-008
1672016d1363024555-f40-lm-restoration-3113-013
1672017d1363024555-f40-lm-restoration-img_0421s
Well, this really is as low as you can go. From where we were to where we are and given where we are my time frame has gone out of the window as like all restoration jobs, this one has ballooned! Bear in mind this car recently went to the Le Mans Classic twice, driven in both directions and apparently never missed a beat.In conditions reminiscent of a Victorian workhouse the chassis is now being blasted back to bare metal and from there the build up can hopefully start in earnest. Interesting to see the central battery position. Suspension parts still being fabricated in Italy by Michelotto but we hope to have them within a week or so but he missed my birthday. Biggest issues remain on what we are to do with the engine etc but more on that to follow.
1672981d1363172272-f40-lm-restoration-f40-lm-lm
1672982d1363172272-f40-lm-restoration-010313-009
1672983d1363172272-f40-lm-restoration-010313-005
1673015d1363176777-f40-lm-restoration-le-mans-2008-cars-etc-118-small
OK, well here is the gearbox all stripped down and unfortunately reverse has developed evidence of heat cracking on the synchro ring. As I mentioned earlier, $15k from Ferrari as that includes first gear and the shaft but we are lucky in the UK to have one of the world’s top restoration companies, Crosthwaite and Gardiner, who, if you can credit it, have recently completed manufacturing, from scratch, an Auto Union D type for Audi complete with V16 as well as a pair of Mercedes W125’s. Check out their website Crosthwaite & Gardiner Fascinating. Consequently reverse gear, I suspect of a rather higher quality than factory, for my little effort should pose few issues. I think we will also be coming back to them for some further engine work but more about that later.In these images welcome to the workings of the F40 gearbox and as I said we are taking the precaution of replacing second gear as that was a weak spot especially with all the extra power.The other picture is off the LSD which was not working properly so we have stripped it down to find the friction plates are worn and useless. Ferrari don’t offer friction plates as replacement parts and prefer you to buy an entire diff so we are examining our options.Is this too much detail?
1674622d1363372748-f40-lm-restoration-img_0413
1674623d1363372748-f40-lm-restoration-img_0414
1674624d1363372748-f40-lm-restoration-img_0415
hilst I struggle with my server and turbo decisions, more progress on the fuel tanks. Here you see them being coated with fibreglass and then we start the Kevlar lay up as in the last photo.The finished articles will be works of art.
1675677d1363530904-f40-lm-restoration-280213-005s
1675678d1363530904-f40-lm-restoration-280213-007s
1675679d1363530904-f40-lm-restoration-img_0416s
1675680d1363530904-f40-lm-restoration-12th-002
Well here is the trail from what they were to what they are. Perfect. In fact so good I would like perspex wheel arches or a clear panel in the wing!Strong, light, durable and to me, a work of art. What’s not to like? It also gives a good idea to you of the standard I am trying to attain with the rest of the project but a very long way to go…..So these now go into storage for a few months. Quite a few……as you will learn shortly
1676261d1363603237-f40-lm-restoration-19213-007s
1676263d1363603237-f40-lm-restoration-1203-005
The Flywheel and clutch.The clutch is no issue and we will replace with an AP race unit. The Flywheel is. Very different from a stock flywheel and yet still road driveable and they have taken literally kilos out of it. Unfortunately the teeth that engage with the starter motor are finished and cannot be remachined and there are other issues so we will need to replace and right now it looks like we might have to make our own and then rebalance with the crank.Anyone have any ideas out there?Chassis now back from being stripped and perpetration is starting and details in the next post.
1677983d1363860560-f40-lm-restoration-12b-006s
1677984d1363860560-f40-lm-restoration-img_0411
1677985d1363860560-f40-lm-restoration-12b-007s
1677986d1363860604-f40-lm-restoration-img_0412s
Looks like we have agreed with a specialist flywheel manufacturer to have a duplicate made, exactly the same but to a higher standard which will take a while. This will probably be mated to a three puck clutch. Meanwhile we are also having reverse gear manufactured and for those interested here is the problem, not on the gears but on the flange. Thery look like scratches but under magnification they are actually cracks. Not cheap as upon inspection by Crosthwaite and Gardiner, it is apparently very complex to manufacture and they should know.
1678494d1363949357-f40-lm-restoration-21-010
An update on the chassis. Now back from having been ‘blasted’ and years of crud stripped away. This will then be primed and expoxyed prior to dry mounting the suspension, then we will finally have a chassis ready to spray the special silver.I am hoping for part of the Michelotto late Birthday surprise to arrive next week which will then enable us to dry mount the suspension and make any changes prior to the chassis paint. That will be really exciting to open as much of it had to be newly fabricated and bought sight unseen! We already know that for some reason the upper wishbone mounts are turned through 90 degrees so there will be work to be done.Maybe three weeks away from real progress?
1678547d1363964416-f40-lm-restoration-photo
1678548d1363964416-f40-lm-restoration-photo5
1678549d1363964416-f40-lm-restoration-photo6
Just a few more general shots of how the car was which may be of interest. This was some weeks ago and so now well in the past.The entire heavy front section has now gone and will be replaced with the lightweight alloy LM structure as posted previously.
1679905d1364206375-f40-lm-restoration-1d213dee918f
1679906d1364206375-f40-lm-restoration-4f8fd301a367
1679908d1364206375-f40-lm-restoration-34c7172a66af
1679909d1364206407-f40-lm-restoration-d1b7f5c874e3
Back to the present.A few shots of the engine in strip down. Blue injector rails and injectors all going off to a specialist to be matched.This is the problem lightweight flywheel and clutch. New flywheel is now being made by Ark Racing a specialist Flywheel manufacturer and they are working with AP who are assembling a clutch for us.The silver lining in the new flywheel is that it will have 60-2 timing pins for accurate setup with the Motec gear, whereas the existing had just 4 rather bent ones, so that would have had to have been addressed anyway.
1680712d1364292202-f40-lm-restoration-b9f2319d7875
1680713d1364292202-f40-lm-restoration-25c3eff6ff3a
Chassis now being sprayed with primer and then two coats of epoxy before a top coat of the Michelotto silver. If only Michelotto would either answer the phone or get me my parts things would be looking encouraging!
1681256d1364381188-f40-lm-restoration-04022013-001
1681257d1364381188-f40-lm-restoration-04022013-005
1681258d1364381188-f40-lm-restoration-20130402-005
1681259d1364381188-f40-lm-restoration-20130402-006
Now two coat epoxied. Next step to dry mount the air new jacks, sort out the roll cage and then look at dry mounting the suspension which, all being well, should be with us next week. Then we get to top coat the chassis with the Michelotto silver. That will mark the start of real progress.And a Happy Easter Holidays to all my (probably few) readers!
1681813d1364488348-f40-lm-restoration-img_0405
1681814d1364488348-f40-lm-restoration-img_0407
1681815d1364488348-f40-lm-restoration-img_0408
1681830d1364488447-f40-lm-restoration-img_0406
Really just for those who are interested to see what the inside of an F40 engine looks like. Hopefully not a sight I will see again.Valves all OK and heads are only a few thousand miles old but seats will still be perfectly matched. One bore slightly scored so that will also be polished out at Crosthwaites. Biggest delay will be the flywheel which is now in manufacture by Ark racing but will take four weeks and we cannot get on with the dynamic balancing until then so will finish engine strip-down and then focus on the chassis which should work well as we expect parts from Michelotto this week. Expect being the operative word.Whilst it is an expensive pain to find all these issues, the plus point is we know we will end up with an absolutely perfect engine and drivetrain, top to bottom, fully matched and better than when it left the factory. Had we not torn it down completely we could have been facing much bigger bills in a few thousand miles.I suppose that is my penance for buying an old race car.
1684618d1364894793-f40-lm-restoration-49e013c78329
1684619d1364894889-f40-lm-restoration-9a63add67ae
1684620d1364894889-f40-lm-restoration-12b-004
Crankshaft out and away for polishing and dynamic balancing. All new bearings will be fitted. Meanwhile work continues of the bodywork with the rear clam being adjusted to accept revised position for air jack inlet which, so as to be road legal, cannot protrude and so has to be slightly recessed.
1685729d1365019543-f40-lm-restoration-14th-010-copy
1685730d1365019543-f40-lm-restoration-14th0203-011
1685731d1365019543-f40-lm-restoration-13th-03-002
We are currently working our way through installation of the air jack system and still awaiting delivery from Michelotto which is causing us a delay. We are fitting a top of the range (read expensive) Krontec system and tidying up the chassis. Then after we get the delivery and dry mount the suspension, finally everything comes off for final chassis silver paint.For those of you worrying about the look of the carbon, don’t, it is just masking tape residue and once the chassis is painted will all be cleaned up.
1686431d1365157486-f40-lm-restoration-14th-025
1686434d1365157486-f40-lm-restoration-25th-0313-012
1686433d1365157486-f40-lm-restoration-14th0203-010
1686432d1365157486-f40-lm-restoration-14th-017
Okay, this is the last post for a few days, but this pm re finally received our first shipment from Michelotto. He has nothing on the shelf so all our suspension has been fabricated especially for us and referenced like a tailor made suit. Beautiful and more detailed images to follow, but here is the front LM unit against another classic Ferrari front hub and brake assembly-any guess what it is from and no more posts until someone gets it?
1686515d1365173834-f40-lm-restoration-tim-f40-009
I have to say that I am actually enjoying posting this thread far more than I thought being able to share my adventure with interested and knowledgeable others, and as a fan, it occasionally seems surreal that I get to deal with Cristiano Michelotto direct. Only last night at 11pm, at dinner my phone rings and I find myself speaking to him and he is e mailing me all the details for the suspension geometry setup, albeit it would be nice if we had the parts to start with!Whilst waiting for someone to get closer on the suspension question before I post more images of our progress, I have to make a tyre, or what you call tire, decision. The only tires that really work on the car are either the new Goodrich G Force Rivals or the Toyo R888. Unfortunately the Goodrich which would be my preferred choice, are not street legal in the UK and whilst it will spend most of its time on the track, it will occasionally venture onto the street. The car would therefore be effectively uninsured.The R888 is almost as good a tire with a crazy tread pattern, as below, which does not really suit the look of the car but will make it handle great on track and on the street. One or two owners here in the UK are using these on their standard F40’s and love them.The final choice is to go back to the old Pirellis, possibly, which look right but simply no longer have the performance.Any thoughts as I am leaning to the Toyos and so as to fir the suspension etc we need a tire?
1687080d1365250584-f40-lm-restoration-img_0556
1687081d1365250584-f40-lm-restoration-img_0557
On the Tyre front, many thanks for the thoughts especially Paul and GV27 which means I might well opt for now for Goodrich and import from the States. One issue is that I really would like a 35 profile rear but it just seems impossible to find although I have one of the top tyre guys in the UK working on it for me and so hopefully will be in a position to make a decision imminently, as I need to so we can move forward on bodywork etc. I can see I may end up with a set of street tyres and possibly a set of track tyres or slicks, not that I have driven much on slicks.Back to the car, as the ‘prize’, have a look at a few details of the Michelotto front suspension. Not a simple bolt on so we will have to make some minor changes to the pick up points, but that will then enable us to move forward and hopefully in 10 days time we might have the rest of the order, ductwork, brakes, anti roll bars, rear suspension, uprights etc.Being racing parts the wishbones have not been treated so we are looking at powder coating or similar. All beautiful very high quality aircraft grade materials.Note the hand written reference on the hub. Tailor made.
1688045d1365349276-f40-lm-restoration-tim-f40-001
1688048d1365349276-f40-lm-restoration-05-013
1688047d1365349276-f40-lm-restoration-tim-f40-003
1688046d1365349276-f40-lm-restoration-tim-f40-006
So we are starting to rebuild our engine as you can see from the attached with all new bearings and now looking to find out the tolerances for pistons and liners but for some reason Ferrari don’t have this information and apparently there are no less than 3 f40 engine rebuilds in the UK stuck for lack of this information.We acquired a workshop manual hoping this would provide the answer-no. Anyone out there have any knowledge? All we have been informed is that the pistons are matched to the liners for clearance and there are various batches used which are colour coded to denote their tolerance but that does not help us.
1689884d1365541959-f40-lm-restoration-14th-007
1689883d1365541959-f40-lm-restoration-14th0203-011
Just had a look at our brand new shiny OZ rims fresh out of the box and at first site, beautiful….until you get closer.Amazing at this price, cannot live with it, so we will have to strip them down and sort them out. Easier than fighting with Italy.
1690780d1365680023-f40-lm-restoration-08-010s
1690781d1365680023-f40-lm-restoration-img_0132
Don’t know if this is of interest to many, but it is to me, as we have stripped the car we have found many small mods that differentiate this race car from a street car. Latest is that due to the far higher loads placed on the suspension through both the wider tyres, slicks cornering and braking loads, not only were the wishbones bespoke and strengthened (for sale if anyone is interested), but even the pick up points have all been beefed up, front and back as in this blurry example.
1691502d1365805001-f40-lm-restoration-img_0120
A little Michelotto suspension detail and part explanation of the cost. Note the TITANIUM extremity for camber control adjustment. Very neat. Very expensiveAnd a pile of rubber which certainly looks like it should grip…But turning the steering wheel at low speeds is going to be a workout.
1692815d1366029794-f40-lm-restoration-dscf1698
1692816d1366029794-f40-lm-restoration-dscf1692
As regards the black gate for the gear lever, I think you should just anodise your existing. A trip to Michelotto would be very interesting as he currently has some interesting cars in there and seems very receptive to genuine enthusiasts. I too hope to make the trip later in the year.Back to the project, a few pics of some details. First is another detail of a beautiful wasted bolt and again shows the attention that goes into some of this race kit.Next up, we found a relative bargain. Turns out the differential was pretty shot and we decided rather than just replace the plates, as the rest was not great, to source a new one from Ferrari which has just arrived. I never want to take this car apart again and hopefully after this rebuild it will effectively be a zero miles car.Finally the gearbox rebuild has started, new bearings, new second gear and we are waiting on our ‘reverse engineered reverse’ from Crosthwaites.Meanwhile, major delivery from Michelotto ‘expected’ early next week which means we can really start to move forward.
1694430d1366277945-f40-lm-restoration-280213-010
1694431d1366277945-f40-lm-restoration-08042013-008
1694432d1366277945-f40-lm-restoration-09042013-034
1694433d1366277970-f40-lm-restoration-img_0128s
Well whilst we are somewhat stuck on resolving our engine and gearbox issues, progress on the front suspension at least. Track rod ends are hanging as bespoke rose joints are awaited from Italy.As you can see, front all now ‘soft’ mounted pending arrival of the rear suspension which needless to say was promised for last week and the week before etc etc but is still with Michelotto. Once we have that we can fit rear suspension and the uprights for the front, all brakes and anti roll bars front and rear and then take it all off again so as to finally start to finish the chassis, getting it top coated in the silver.Then we can start to move forward properly and to have a finished effectively rolling chassis would be a major landmark, probably even a half way point?
1695906d1366555811-f40-lm-restoration-009
1695910d1366555852-f40-lm-restoration-08-003
1695912d1366555893-f40-lm-restoration-08-002
For those interested in the detail, acting on C Michelotto’s advice, we are changing the longer geared Euro spec Crownwheel and Pinion for the shorter geared USA version. This car was apparently timed at 227 MPH with the Euro version, but it is a rare track where you can avail yourself of this, hence the decision to add even more to the acceleration potential.Like the toffee coating?
1697084d1366718463-f40-lm-restoration-19042013-001
1697085d1366718463-f40-lm-restoration-19042013-005
For those who are interested in the set of LM style OZ rims I promised to post a pic or two. Apologies for the quality but this gives you an idea, unmarked, and they should slot onto the standard hub.
1697848d1366818567-f40-lm-restoration-16-029
Thanks for all the interest and support. Strange, I never thought I would enjoy posting the journey as much as I do, I thought it would be quite trying but in fact the reverse. Very satisfying to share the ups and downs of this adventure with all enthusiasts here with varying levels of knowledge resulting in many useful thoughts and opinions, but all bonded by a common love of the Marque. Brilliant.Meanwhile, CM made a delivery! Yes, 8 weeks late but look what turned up, two sets of rear wishbones assemblies. I will post more once we have had the chance to unpack properly. Apparently the anti roll bars etc are due to leave Italy today and the brakes etc tomorrow. We shall see, but all being well, we might have all these vital components within a week or so and then we can really crack on, at least with the chassis etc.
1698451d1366912426-f40-lm-restoration-20130424-001
No sooner said than done…………Some delicious detailing
1698716d1366972672-f40-lm-restoration-250413-018
1698720d1366972761-f40-lm-restoration-250413-011
1698724d1366972882-f40-lm-restoration-250413-010
1698725d1366972882-f40-lm-restoration-250413-004
1698733d1366973350-f40-lm-restoration-25th42013-159
So now we have the front and rear suspension just about mounted. Few alterations needed and the works of art will shortly be in place. Interestingly I note that the front uprights are made of Avional, apparently a super strength lightweight Swiss alloy (had to look that one up) and the rears are Magnesium, again, all with Titanium adjustment. Expensive, but you begin to understand why.Now we have all the set up info from Michelotto we are fine checking with computerised Spanesi Touch system to ensure everything is absolutely spot on.Adjustable LM brakes, adjustable anti roll bars, Carbon Fibre ducting, Magnesium pedal box, master cylinder and light weight Konis etc are hopefully incoming tomorrow!! Hopefully.Everything will be offered up to the chassis, adjusted and fixed before disassembly for final chassis paint.Got to love those rear tyres!I am hoping that by the end of next week, we might finally be in the paint shop…….maybe
1700942d1367312967-f40-lm-restoration-26th-006s
1700943d1367313351-f40-lm-restoration-tim-30th201304-006s
1700944d1367312967-f40-lm-restoration-friday-009s
1700946d1367313131-f40-lm-restoration-26th-4-2013-002
1700947d1367313351-f40-lm-restoration-29th42013-008s
1700948d1367313351-f40-lm-restoration-29th42013-003s
Just a small update. Nothing from Michelotto-disappointing but not unexpected. More chasing but then the day is still young.Meanwhile we have been finishing off the LM front assembly so all we now need is a delivery to finish mounting and checking everything before the paint shop beckons.
1702075d1367485999-f40-lm-restoration-08th-011s
1702074d1367485999-f40-lm-restoration-img_0124s
Gear box rebuild now well underway. New bearings, new 2nd gear and shorter ratio crown wheel and pinion all being installed. Then it is off to Crosthwaites for fitting of reverse and final set up and result a zero miles gearbox.Another partial delivery from Michelotto to include LM brakes, magnesium pedal box, carbon fibre cooling ductwork, track rod ends etc etc and I will post pics of these once unpacked, but frustratingly we are still short of the lightweight Koni shocks and springs which we need to be able to set the ride height and deal with the bodywork before final chassis and body paint and final assembly, so blame Michelotto for the shortage of posts. Apparently leaving Italy today but I have heard that before!
1705746d1368092686-f40-lm-restoration-1ish-007s
1705747d1368092686-f40-lm-restoration-1ish-033s
1705748d1368092686-f40-lm-restoration-07-may-13-003s
Last post for a week or so or until Michelotto delivers the springs and shocks.Body now back on temporarily to sort ride height, clearances, panel gaps etc but to do it properly we need shocks if you are reading this Cristiano-Please! In theory sent last week but I have heard that before……..please prove me wrong!
1706555d1368263834-f40-lm-restoration-031515-013s
1706556d1368263834-f40-lm-restoration-031515-003s
Well here we are with a few more parts from Michelotto. LM brakes and discs, LM magnesium pedal box with front/rear bias controller, LM anti roll bars, track rod ends (now fitted as per pic), carbon cooling ducts etc etc, but not the lightweight shocks and springs which we are still waiting for.Please Cristiano, we need them.
1708328d1368556817-f40-lm-restoration-tim-08-f50-008s
1708329d1368556817-f40-lm-restoration-tim-08-f50-002s
1708330d1368556817-f40-lm-restoration-tim-08-f50-003s
Better pic of track rod ends installed and completed front assembly
1708576d1368608754-f40-lm-restoration-tim-08-f50-008ss
TREASURE! Finally it looks like we have our missing parts which is great news.
1708624d1368627341-f40-lm-restoration-sir-tims-parts-008-2-
1708680d1368634753-f40-lm-restoration-lord-simonds-photos-039s
1708681d1368634753-f40-lm-restoration-lord-simonds-photos-013s
Work has started in earnest on the body. All panels have been refitted so as to start panel alignment and weight will be added to engine bay so as to represent engine in position and ensure that the panels are gapped ‘under load’.Underside of front clam was a mess so that will be prepared and brought up to standard with new ductwork etc.Gradually moving closer to paint, chassis and body, indeed at least we are now in the body shop! Cannot wait and will update further after visiting the shop tomorrow.
1711063d1369040082-f40-lm-restoration-tin-f40-14th-032s
Some further shots of the front clam.Here you can see our original clam before and midway through the restoration process. We have taken literally pounds of filler out of it, so much that you can easily tell the difference just by lifting it. It will be finished off with new arches and ductwork and then a final internal layer of Carbon Kevlar so it will be both lighter and stronger (and more beautiful) than where we started.
1712389d1369146299-f40-lm-restoration-img_0011s
1712388d1369146299-f40-lm-restoration-tin-f40-14th-001s
And how we got there, or rather poor James in the DIY spacesuit did……
1712433d1369158170-f40-lm-restoration-dscf2365s
1712432d1369158170-f40-lm-restoration-dscf2366s
Whilst we labour for the next few weeks to get the bodywork perfect, progress is actually being made elsewhere mechanically. Engine is now in all its component parts and we have been working on the gearbox which is now ready for its new gears and awaiting the Crosthwaite and Gardiner reverse which they are apparently making to a higher quality than Factory as you would expect from such a firm. New crown wheel and pinion with shorter gearing installed as well as new differential and bearings and once we have reverse, the gearbox will be finished up.In these images you can see the backlash being set up with a dial gauge and also the crown wheel and pinion being painted with engineer’s blue to check mesh engagement. Last shots, all finished up and ready for the gears.Once finally assembled all casings will be resprayed.
1713425d1369341448-f40-lm-restoration-sir-tim-f40-1-s
1713426d1369341448-f40-lm-restoration-sir-tin-f40s
1713427d1369341448-f40-lm-restoration-img_0002s
1713428d1369341448-f40-lm-restoration-photo3s
For those of you interested in the detail of what must be one of the world’s most expensive pedal boxes. Next to it is the original so you can get an idea of the difference. And the quality.This was, like everything else, not a stock item, but being a magnesium casting was not viable to be made in a series of one. We were however very fortunate to be able to piggyback on an order from the Sultan Of Brunei who purely coincidentally had to replace two of his on his LM’s which have rotted away in the humidity of their non air conditioned storage and needed replacement. Good timing as otherwise I am not sure what we would have done.The cable attached to the clutch pedal is the front/rear brake bias adjuster which ends up on the dashboard.
1715160d1369651388-f40-lm-restoration-img_0019s
\
1715161d1369651388-f40-lm-restoration-160113-001s
Temporary engine in place so that all the panels can be correctly gapped ‘under load’.Front clam now well on the way to paint…..
1716701d1369908376-f40-lm-restoration-photo3a
1716702d1369908414-f40-lm-restoration-tin-f40-14th-027s
More images of prep work on the body. All old and defective panels such as cooling ductwork and wheel arches are being renewed in Kevlar as appropriate. A lot of work to return it to as new. Side pods are now off so we can get access to the final part of the chassis for paint, and yes it looks like paint next week! That is truly exciting and finally as opposed to digging a hole we can start to fill it in. A potential turning point and I find myself wishing away time.
1717689d1370042152-f40-lm-restoration-dscf2584
1717690d1370042152-f40-lm-restoration-img_0005
1717691d1370042215-f40-lm-restoration-14th-may-003
1717694d1370042329-f40-lm-restoration-31-007
We took the block off to Crosthwaite and Gardiner who checked them all thoroughly and said they were actually all OK, the slight scar was merley cosmetic which was a relief. They are fitting new piston rings, LM style titanium conrods and once the crank is back from repolishing and the new flywheel delivered, we can start a slow assemble. I think the chassis will probably be ready ahead of the engine but that is no bad thing. Very comforting to have Crosthwaites involved with their reputation and abilities, probably one of the World’s best : www.crosthwaiteandgardiner.com – fascinating to see what they get up to.
1717949d1370093198-f40-lm-restoration-1403-007
Cam lobes were slightly worn but enough meat on them for a grinding so they have gone out to a specialist. So right now that means crank is out for repolish and new bearings, LM Titanium conrods in manufacture, lightweight flywheel in manufacture, cylinders being rehoned as necessary, turbos/manifolds being built up and inlet trumpets will all be stripped down, cleaned and parts replated as necessary. All taking place at different specialists and one fine day the jigsaw will be reassembled.Apparently, even in its sorry state it was recently recorded on the dyno at 650BHP at the rear wheels, so looking for a little more by the time we have perfected it, a more ‘reliable’ 700 is the target but this time with the suspension and brakes to handle it.
1719083d1370254996-f40-lm-restoration-img_0017s
1719084d1370255031-f40-lm-restoration-dfc4a6b3ac9d
1719086d1370255133-f40-lm-restoration-2401-021s
1719088d1370255440-f40-lm-restoration-img_0127s
Well finally, hopefully, the last shots you will see of the old.We are now taking up all Mototechnique’s spraying facilities. Chassis stripped of all roll cage and stregthening in one paint bay for final prep and paint next week, and all body panels in other paint bay for final prep and primer this week.Then we can start to put Humpty back together again.And yes, for those really paying attention, I know about the front tyres!
1719790d1370340196-f40-lm-restoration-31st-052013-031s
1719791d1370340196-f40-lm-restoration-31st-052013-023s
1719792d1370340196-f40-lm-restoration-31st-052013-007s
A few pics of the body panels in prep. Laying up the new Kevlar underneath the front clam so now light and strong. Plan is to get primer on the roof and chassis this week and then all being well colour next.Reason for the increase in images is trippling in manpower which, once we have the chassis and body sorted will mean things drift back to normal which from a financial viewpoint is comforting.
1720364d1370430569-f40-lm-restoration-2401-004s
1720365d1370430569-f40-lm-restoration-31st-052013-002s
1720366d1370430569-f40-lm-restoration-2401-016s
1720367d1370430633-f40-lm-restoration-dscf2682s
Meanwhile, we are sending the inlet manifolds off for the Zircotec finish as keeping the charged air cool is clearly a plus and anything we can do to reduce the temp of these will be a good start.Meanwhile a few more pics of progress. Here you can see the last photo (I promise) of the chassis pre final paint, the areas where we have been working on the jacking system etc being two pack expoxied before the mist coat and top coat are applied next week. Final prep for various panels and they are being primed today whilst the new fuel filler caps are blended in and the work comes to an end on the sills. All being well, everything except the front clam will at least be in primer next week, and chassis painted.
1721424d1370600784-f40-lm-restoration-04-006s
1721425d1370600784-f40-lm-restoration-04-008s
1721426d1370600784-f40-lm-restoration-5thjune13-010s
1721427d1370600784-f40-lm-restoration-5thjune13-008s
A final shot for the weekend that has just come in which I had to post as so pleasing. New filler caps now all neatly feathered in and panel just about ready for primer next week.
1721533d1370621447-f40-lm-restoration-2013-06-07-13.09.07s
Just looking through the photos from last week and one recent one shows the chassis now with a mist coat so as to reveal any minor aesthetic imperfections in the frame which can then be dealt with. You can also now clearly see the refitted rear air jack mounts.Note in the background that she is in good company in the workshop, in one instance quite humbling.
1722757d1370792484-f40-lm-restoration-5thjune13-007s
Meanwhile, for the first time in a long time excitingly the upper and lower rear clams are now finally in one colour. In case you thought they were destined for Chris Evan’s White collection, they are not but at least it is primer and I begin to feel we are coming out of this tearfully expensive hole. These sort of jobs are quite draining in more ways than one as you keep on having to write out cheques and yet the car looks worse and worse and it gets more and more depressing until you finally reach bottom and start to climb out and I think that is almost where we are. Maybe another two weeks to be confident that it is all not a waste of time, effort and money but now beginning to feel more positive.Work continues on the front clam but still a week or so away from primer as so much detailed work on wheel arches and all the Kevlar ductwork which is quite extensive on the LM. That should be a work of art when finished and be interesting post before and after shots.
1724058d1370942140-f40-lm-restoration-5thjune13-001s
1724059d1370942140-f40-lm-restoration-5thjune13-005s
Aside from the finished fuel tanks and Michelotto parts, finally another finished item in the shape of our Motec gear arrived today as this seems the most reliable and adjustable kit out there (with great knowledgeable local support), well proven in racing F40’s and appears very similar to some Michelotto LM’s (as attached) when their old digital board gives up. Nice to have a few finished items appearing as the jigsaw pieces start to arrive from different quarters. What we really need next is a reverse gear from Crosthwaites so we can finish the gearbox.Not quite sure whether to fit the change up lights or not-pondering……
1724184d1370975934-f40-lm-restoration-photo2
1724185d1370975934-f40-lm-restoration-img_0027s
1724186d1370975934-f40-lm-restoration-img_0024s
Another part of the jigsaw arrives.Latest 3KG Lifeline 360 extinguisher system just arrived. Used to only be available as 2.25KG but literally just released the larger version. Four nozzles in the engine bay, 2 in the cockpit and no mess to clear up if ever used. I hope not but these cars, as already pointed out on this thread, do occasionally have a issue.
1724857d1371114589-f40-lm-restoration-img_0177_zpsa7c5eebb
A lot of work going into what was a pretty ratty front clam. Here you can see some of the Kevlar being laid up, wheel arches being bonded in and preparation being made for the ductwork. What a change – kilos of weight removed and we are ending up with a lighter stronger unit from where we started. Another week to go on this and then all the bodywork will be behind us.
1724952d1371141731-f40-lm-restoration-2401-018
1724953d1371141768-f40-lm-restoration-06-june-13-030s
1724954d1371141800-f40-lm-restoration-06-june-13-025s
1724955d1371141827-f40-lm-restoration-2013-06-10-07.44.25s
Starter motor has been sent away for matching to the new flywheel, which is currently in manufacture and due in a week or so, and will be overhauled at the same time.Final prep work underway to the underneath of the sills and these will be in primer early next week.Just another arty shot of the front clam lay up on-going. A lot of detailed and intensive work here.
1725484d1371208556-f40-lm-restoration-5thjune13-010s
1725485d1371208556-f40-lm-restoration-2013-06-07-13.11.45s
1725486d1371208556-f40-lm-restoration-dscf1356s
If you look back through the thread there are images of the brakes that were fitted during the cars racing era which were Group C, allegedly off a 962 Porsche. The only sensible alternative today are made by Brembo and they offer an upgrade for the standard F40 as attached (last pic shows difference) but you need the bigger rims to fit the discs. We have full LM units which are very different, different discs, calipers, pedal box, master cylinders etc. (see a few pages ago for pics)We are fortunate in that the car started its race life already one of the 27 LM/GTE conversions as to convert a standard road car to this spec would today be even more eye watering and possibly not an enhancement investment wise given the high value/cost of a road car. Aside from the obvious, there are just so many details that separate a road car from an LM, but even then you would not have that vital race history.
1726222d1371383146-f40-lm-restoration-dsc02682
1726223d1371383146-f40-lm-restoration-dsc02685
1726224d1371383146-f40-lm-restoration-dsc02687
That is exactly my aim, to create a car that can be used rather than become a garage queen, and hopefully finished to a higher standard than any of the competition and good for another 25 years.Meanwhile, we have rear clams in primer and finally side pods in primer, all looking very neat and tidy with faired in fuel caps etc, just waiting for the final front body panels to join them.Next up refit the suspension (again) and the panels to the chassis, line up all the panels so as to get the gaps correct in situ, something Ferrari never did, make final adjustments and then actually paint the panels red! Meanwhile front clam, which can be treated separately and in relative isolation to the rest as it only has a junction with the chassis rather than other panels, can be done once we have finished all the ductwork. Then all the suspension has to come off again (4th time) for chassis paint.I feel I just about have my fingertips on the edge of the hole now-maybe a couple of weeks before final assembly actually starts and I can see out of it.
1727199d1371549341-f40-lm-restoration-dscf2800s
1727200d1371549341-f40-lm-restoration-dscf2806s
1727201d1371549341-f40-lm-restoration-dscf2805s
1727202d1371549341-f40-lm-restoration-dscf2803s
Well two steps forward one step back. All the main panels primed and fitted, save for the front clam, all married up and pretty much ready for paint. Or so we thought.
Rear suspension off again and then on for the 4th time to sort hand brake(to make it street legal)and soon to come off again.Then turns out a well known weakness of these cars is for the chassis member to rub against the inner side of the rear clam by the engine bay glass and create an annoying squeak. This has reared its head on this car as you can see being inspected in the 4th pic. So just as we thought we were going red, rear clam has to come off, wax mold made of offending chassis member, clam adjusted, and then of course as the clam will sit slightly lower,we will have to rematch the panel fit. Again.Silver lining, at least by doing it thoroughly and right, we won’t have to repaint the clamTired of 50 shades of grey………
1728906d1371840573-f40-lm-restoration-12th06-006s
1728907d1371840573-f40-lm-restoration-06th-june-005s
1728908d1371840573-f40-lm-restoration-12th06-012s
1728909d1371840573-f40-lm-restoration-12th06-035s
1728910d1371840640-f40-lm-restoration-12th06-038s
Work has started on eradicating that annoying squeak where the frame member rubs against the rear clam. Wax mould taken, clam adjusted and then refitted with resulting re gapping of panel joints.
1730058d1372091005-f40-lm-restoration-13-th-june-13-003s
1730060d1372091402-f40-lm-restoration-120613-011s
Work going well on the front clam and looking to have it in primer by the weekend. Despite life being too short, we are putting a humungous amount of time and effort into this panel and still have some way to go but a long way from where we started. And squeak free.
1730766d1372168091-f40-lm-restoration-13-th-june-13-005s
1730767d1372168091-f40-lm-restoration-13-th-june-13-007
1730768d1372168091-f40-lm-restoration-14th-june-010s
1730769d1372168091-f40-lm-restoration-14th-june-013s
Meanwhile back in the real world, the apparently to be accepted squeak has now been dealt with and the panels re-gapped but it has delayed the plan to get the primer on. This 50 shades of grey thing seems endless.Getting closer.
1731373d1372261319-f40-lm-restoration-19th-june-13-012s
1731374d1372261319-f40-lm-restoration-19th-june-13-013s
Suspension on again for the fourth time! And then only needs to come off once more for painting and chassis paint. Then it goes back for real.
1731886d1372347927-f40-lm-restoration-12-001s
1731887d1372347927-f40-lm-restoration-12-015s
More work on the front clam to sort out the ductwork, then back on to check before going back into the body shop for final prep but there are still two final ducts that cannot be fitted until we have the radiator in place.
1732553d1372445012-f40-lm-restoration-17th-june-13-016s
1732552d1372445012-f40-lm-restoration-17th-june-13-007s
1732554d1372445012-f40-lm-restoration-19th-june-13-001s
1732555d1372445012-f40-lm-restoration-14th-june-006s
Couple of other shots from last week. More work on the front clam and appreciate the background.The quality of cars passing through Mototechnique’s workshops is truly amazing. More to follow….
1733024d1372523616-f40-lm-restoration-19th-june-13-006s
1733025d1372523616-f40-lm-restoration-130625-004s
Back in the paint shop, hopefully now with definite intent of colour, and the final shots, I think, of the prepared and un-painted front clam. Wednesday it will be in primer.Work continues on final preparation and the rear panels and roof are just about ready for paint having been primed and baked. We will see colour this week!Hopefully also a week of deliveries as we assemble all the parts out being made/treated by specialists. Manifolds with Zircotec coating, new turbos again Zircotec treated, new lightweight flywheel and clutch, reground camshafts and maybe even our re-polished crank. Or at least that is the plan, but to be honest we are not being held back so none of this is on the critical path, as yet.
1733738d1372669120-f40-lm-restoration-19thy-004s
1733739d1372669120-f40-lm-restoration-19thy-007s
1733740d1372669120-f40-lm-restoration-19thy-012s
1733741d1372669120-f40-lm-restoration-19thy-017s
Just look what the Postman surprised us with today – our Zircotec treated inlet manifolds!For those who are unaware, Zircotec is a ‘plasma-sprayed ceramic coatings to protect components from the effects of fire, heat, wear, abrasion and corrosion’. In this instance it will help keep our charged inlet air at a lower temperature which means ‘increased engine performance, eg. a 30 degree C drop in intake air temperature can deliver a 6% increase in power, or can increase engine efficiency leading to less fuel usage’.Used extensively in F1, Nascar, GT racing, Classic cars etc, this hot engine bay seems to be the place to use it and we will also be applying their process to both our exhaust manifolds and hot side of the Turbos.Another work of art to be set alongside the Carbon tanks, Michelotto suspension etc.Yet again, note the background car, yet another classic into their shop for a bit of work.
1734121d1372711260-f40-lm-restoration-june-007
1734122d1372711328-f40-lm-restoration-june-006
The very last shot of the front clam before we apply polyester spray filler, a sealing coat which will tie all substrates together before final finishing and full priming. Just checking the Perspex headlight covers for a perfect fit and then off to the spray booth tomorrow.Some colour by the weekend? Not on this panel, but hopefully elsewhere.
1734639d1372794556-f40-lm-restoration-2506-012s
1734640d1372794556-f40-lm-restoration-210613-001s
You will all be relieved to see that you never have to look at any more shots of the multi-hued front clam undergoing work (except on the underside) and it is finally close to joining the other panels in grey primer. This polyester spray filler bonds the various substrates and then into the oven before final finishing and grey primer tomorrow. Relief.Thanks Greg for you post and after all this work I too really do hope it pays off in years of enjoyment-this is a long haul and if you read back through the thread there was a stage I thought it would be over in 4 months. Ridiculous knowing myself and my goals.
1734935d1372843071-f40-lm-restoration-26-010s
1734936d1372843129-f40-lm-restoration-26-005s
Finally a glimpse of colour over the lip of the moneypit!F40’s apparently were painted in slightly different shades of Rosso Corsa during their production cycle ranging from a darker red to one with a slightly more orange tint. We have gone for the slightly darker shade and apparently I now have to choose whether we go for an old fashioned ” Coach builders” full flat and polish finish which removes all ” Flow ” (Orange peel is a chunky effect whereas ” Flow is a smoother gun finish) or we lightly sand to leave a more natural finish – Any thoughts?Next up, before the week end, is for the chassis to go silver and that means real progress.
1735506d1372927296-f40-lm-restoration-27th-june-008s
1735507d1372927296-f40-lm-restoration-27th-june-017s
CLICK HERE for Part 2…

39 thoughts on “Ferrari F40 LM Restoration Part 1”

  1. This is the kind of article you really want to savor. Outstanding work documenting everything Anth! This is one of my all time dream cars and I can’t wait to see Part II!

  2. the best reading material of my week! to the very end of details..please post more on the remaining parts
    thanks!

  3. ok i scrolled down and breezed thru the thread then bookmarked it. This deserves a quiet time and go through it again in detail one lazy afternoon.

  4. Wow. this has to be the longest build post I’ve ever read in one go! Thanks very much for your effort in putting together this epic post! I spent an entire afternoon poring over it!

  5. If by “another forum” you mean this site, then yes, he does know, because I asked for his permission and he obliged.

  6. Thank you for sharing with us such a build! Had a Christmas present in the summer! and that ferrari engine torn apart, just awesome!

  7. i like this new format! i killed 2 hrs on this one post just going over it all.
    wonderful. more like this please!

  8. am I the only one who doesnt mind going page by page? Its easier to reference where you left off when you have to return to finsih. That being said, excellent post! I spent a couple hours reading everything and looking at the pics. Inside the rear clamshell, the finish work at the cabin, is very slick

  9. awesome car, but the owner sounds boring, like he just wants to show off …
    the car is mythic, but there are many builds one this site that are way more interesting ! here, it’s just an assembly of various parts and renovation of a body and moteur !
    not like, for exemple, the volvo 4 rotor build where the guy build almost everything HIMSELF (and with humility, not saying all the time “that is one of the most expensive … etc”)

    but awesome car ^^

  10. Excellent. Okay, not wild and ridiculous like the four rotor Volvo. But a great format and lots of detail which was insightful. I liked not having to trawl from page to page wading through comments. It was also great to be enlightened by the visuals of an F40’s “inards”. In some regards a pretty basic car and in others pushing what was being done in its era were, but of course, taken to “road car” extremes. I will guess that some of the younger followers did not look at it and learn (I learnt at least two remarkable details as to how Ferrari solved a suspension issue in a way I’d never seen before). It does help to read the text rather than solely scan for images of something wild. Whether one thought this was excellent or not might come down to the purpose they read these posts: did they want to be entertained, or did they want to learn something that could be taken away and applied?

  11. Loved reading this, was especially helpful having only the owners comments and pictures to read through.

    Still can’t quite get my head around those rear suspension pickup points. Looks like all the joints are set up for movement in the horizontal plane yet the tyre should move vertically. Unless theres only a small amount of movement allowed and it occurs in those joints?

    No idea but fantastic to see. Was a little hard to see where all the filler in the bodywork was when the final images seemed to show more but I realise surface area and depth are different. Loved the carbon kevlar pieces

  12. O.M.G.
    wow.

    and I must have that silver colour code…would be nice to share that info.

  13. wauw 🙂 can’t wait to see more 🙂

    will help me a lot with my project, thanx a lot 🙂

  14. @brenden- I too was wondering about the inner suspension pick up points not looking like they would allow vertical movement?

    Otherwise- yeah so the guys got heaps of money.. At least he is spending it on having an all time great supercar restored and we get to watch. It is fantastic to be able to see the details of how a F40 is put together.

  15. Very cool build, and I love not keeping the purists happy.

    Oh the marks on the turbo blades are for the operator to know what angle the cut he needs to make to balance the impeller.

  16. To whom it may concern,

    I own an F40 that has had a similar restoration done.
    I am very interested in the OZ wheels if you are selling a set.

    Please email me at jfaro@tuscanbrands.com.

    I’m curious to know how long the restoration took.
    My car took almost 7 years.

    Best of luck with her. She looks beautiful.

    Regards,

    Joe Faro

  17. I’m making a 1/16 scale model of a F40LM, and find your explanations and photos of great assistance. Thank you for your outstanding “diary” of progress. Wonderful reading. Regards, Gerry

  18. This is what I call an amazing job , its surprising what you can do with a lot of money

  19. Hi, this may be what your post recently was about, but are you aware that ‘lowmileage’ on YouTube has ripped off the photos from your F40 thread? I can’t report it for copyright infringement, only the copyright owner can, but i have reported it as spam or misleading.

    This particular channel keeps coming up in my recommended and all they do is rip off others work to create some frankly boring slide shows. Without the description and background and with the photos in a random order, they’re just very dull….

  20. Hi mate, yes I am aware and am very disappointed, but there’s not much I can do. Like you said it’s up to the copyright owners to say something. Sad times we live in, integrity is obviously not important any more. Thanks for your message, means a lot.

  21. Just wanted to say that I have been visiting this thread for about 3 years now. It never gets old.

    I worked at a Ferrari dealership in the States from the late 80’s – Early 90’s. We had some incredible machines come through but the days I was able to drive the F-40 are the ones I remember most.

    Absolutely incredible.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.